← Back to the blog

What CdA does my rider need? Lessons from the 2026 Tour time trial

AerodynamicsUpdated 7 min readBorja Alfaraz

2026 Tour time trial

+1:51

How much longer the demo plan would have taken, at the same power, with a CdA of 0.22 instead of 0.176 m².

Calculated with the SuperRecord engine on the Évian–Thonon time trial (26 km). At 0.20 the gap is already a minute.

When a rider sees a Tour winner’s CdA, the question comes by itself: what should mine be? The coach’s job is to turn that curiosity into a useful target: a number the rider can reach, that can be measured, and that translates into seconds in their own race. The 2026 Tour time trial in the SuperRecord demo is the starting point.

How much is CdA worth in a real time trial?

The demo reproduces the 32:19 of the Évian–Thonon time trial with a CdA of 0.176 m² and 71 kg for rider and bike. Keeping the same power plan and changing only CdA:

CdA (m²)Average speedExtra time
0.176 (demo)48.3 km/hreference
0.1947.4 km/h+37 s
0.2046.8 km/h+1:02
0.2245.7 km/h+1:51
0.2444.7 km/h+2:37

Table 1. The same demo power plan with different CdA values. Calculated with the SuperRecord engine on the 2026 Tour time trial, 11 km of climbing included.

Even with 11 km of climbing, each hundredth of CdA is worth around half a minute over 26 km. On a flat time trial it would be worth more, because more time is spent at high speed.

Why does copying a professional’s CdA not work?

  • It depends on size: CdA measures the drag of the whole system, and most of it comes from the rider’s body, not the bike2. A taller or broader rider starts from a different number.
  • It depends on effort: in professionals, drag while pedalling at race pace was 31 % higher than in a static position1. A CdA measured static or at low intensity is optimistic.
  • It depends on how it is measured: wind tunnel, velodrome and road do not give exactly the same value3. To compare your rider with themselves, always use the same method.
The key point. The useful target is not someone else’s CdA, but your rider’s own a few months from now, measured the same way as today and at race pace.

How do you set a realistic CdA target?

  1. Measure the starting point on the current bike and position, at time-trial pace (see how to run a CdA test).
  2. Estimate the margin: in professionals, position work cut drag by 14 %1. A rider who has never worked on position usually has more room than one who has.
  3. Translate it into seconds in the target race: the same change is worth more on a flat time trial than on a hilly one.
  4. Check power in the new position: a lower CdA that costs watts is not an improvement.

An example: a 250 W rider, 78 kg with the bike, with a CdA of 0.26 m², takes 60:45 for a flat 40 km time trial. Getting down to 0.24 saves 1 min 31 s; reaching 0.22, 3 min 7 s. Doing the same with power would take going from 250 to about 268 W in the first case and to about 289 W in the second, 16 % more, and field-measured CdA is closely linked to flat time-trial performance4.

What changes over the season?

  • A reference CdA for each bike and position, reviewed at the start of each time-trial block.
  • Sessions in position: the target CdA only counts if the rider holds it for the whole event.
  • Equipment afterwards: helmet, skinsuit and wheels are tested on the position once it is set, never before. In professionals, the aero helmet was not better for everyone1.

How do you take it into the race?

With a measured CdA, the power plan and predicted time stop being a generic estimate and become your rider’s own. And after the race, comparing the actual time with the predicted one by section shows whether the day’s CdA matched the tests or whether the rider lost position somewhere.

Frequently asked questions

What is a good time-trial CdA?

It depends on the rider’s size and on how it is measured. What matters is that it drops against their own previous value, measured the same way.

Is it better to work on position or power?

It depends on the course. We explain it with numbers in power or position before a time trial.

In the demo on the Tour time trial you can change CdA and see the time instantly.

References

  1. García-López J, Rodríguez-Marroyo JA, Juneau CE, Peleteiro J, Martínez AC, Villa JG. Reference values and improvement of aerodynamic drag in professional cyclists. J Sports Sci. 2008;26(3):277-86. doi:10.1080/02640410701501697
  2. Crouch TN, Burton D, LaBry ZA, Blair KB. Riding against the wind: a review of competition cycling aerodynamics. Sports Eng. 2017;20(2):81-110. doi:10.1007/s12283-017-0234-1
  3. Debraux P, Grappe F, Manolova AV, Bertucci W. Aerodynamic drag in cycling: methods of assessment. Sports Biomech. 2011;10(3):197-218. doi:10.1080/14763141.2011.592209
  4. Peterman JE, Lim AC, Ignatz RI, Edwards AG, Byrnes WC. Field-measured drag area is a key correlate of level cycling time trial performance. PeerJ. 2015;3:e1144. doi:10.7717/peerj.1144

Related articles