Should I work on my rider’s power or position before the time trial?
Decision example
74 s / 5 s
What 15 W more and 0.010 m² less CdA are worth on a 10 km climb at 6 % for a 300 W rider.
On a flat 40 km time trial, the same changes are worth 58 and 45 seconds. Model calculation with 78 kg and a CdA of 0.240; an example, not a real case.
Eight weeks to the target time trial and only so many training hours. Do you spend them raising watts, working on position or both? The answer depends on the course more than on the rider, and you can put numbers on it before planning the block.
What decides the answer?
The speed at which each section is ridden. The faster the rider goes, the more the air matters and the more a lower CdA pays; the slower, the more weight matters and the more extra power pays4. That is why the same gain is worth very different amounts depending on the profile:
| Course | 15 W more | 0.010 less CdA |
|---|---|---|
| Flat 40 km time trial | −58 s | −45 s |
| 10 km climb at 6 % | −74 s | −5 s |
Table 1. Example of a 300 W rider, 78 kg with the bike and a CdA of 0.240 m². Model calculation.
The case: the 2026 Tour time trial
The Évian–Thonon time trial mixes both: 11 km of climbing, 6 of fast descent and 9 of flat. With the SuperRecord demo plan, 15 W more over the whole course would have saved 34 seconds, and cutting CdA by 0.010 m², 27. But the split by section is what guides the work:
On the climb, watts win by almost three to one. On the descent and the flat finish, CdA wins. A rider who will decide the time trial on the climb needs watts; one who will lose it on the flat needs position.
Which is easier to achieve with your rider?
The table says what each change is worth; the coach has to set next to it what it costs. Raising the power of an already trained rider is slow. Position, on the other hand, can be improved in a few sessions: in professionals, changing position alone cut drag by 14 %3. When the cost of each improvement is weighed against its return, aerodynamics tends to compare very well with training or equipment1, and field-measured CdA is closely linked to flat time-trial performance2.
What changes in the preparation block?
- Fast time trial: a CdA test at the start (see how to run a CdA test), training on the time-trial bike and long blocks in position so power does not drop in it.
- Time trial with a decisive climb: power work at the duration of the climb, and rehearsals of the climb in the time-trial position if the rider will ride it on the extensions.
- Mixed time trial: the split in the figure gives the proportion. In the Tour one, the climb is more than half of the race time, so watts weigh more, but CdA cannot be ignored.
How do you take it into the race?
Position work only pays if the rider holds the position. In the briefing, mark where they must not leave the extensions (descents and fast flat, where CdA rules) and where they can afford to at almost no cost (slow ramps). The section-by-section power plan already accounts for that difference.
Frequently asked questions
What about weight?
On the flat it barely counts; on climbs it does. There is a gradient beyond which it outweighs aerodynamics: see weight or aerodynamics.
What CdA should my rider have?
It depends on their size and position. Benchmarks and a real case in what CdA does my rider need.
You can move power and CdA in the demo on the Tour time trial and see the time change instantly.
References
- Jeukendrup AE, Martin J. Improving cycling performance: how should we spend our time and money. Sports Med. 2001;31(7):559-69. doi:10.2165/00007256-200131070-00009
- Peterman JE, Lim AC, Ignatz RI, Edwards AG, Byrnes WC. Field-measured drag area is a key correlate of level cycling time trial performance. PeerJ. 2015;3:e1144. doi:10.7717/peerj.1144
- García-López J, Rodríguez-Marroyo JA, Juneau CE, Peleteiro J, Martínez AC, Villa JG. Reference values and improvement of aerodynamic drag in professional cyclists. J Sports Sci. 2008;26(3):277-86. doi:10.1080/02640410701501697
- Martin JC, Milliken DL, Cobb JE, McFadden KL, Coggan AR. Validation of a mathematical model for road cycling power. J Appl Biomech. 1998;14(3):276-91. doi:10.1123/jab.14.3.276
Related articles
- Time trialGarmin Power Guide in a time trial: how it works and where it falls short7 min read
- Time trialHow to analyse a time trial with power after the race: what to look at and how to explain it to your rider7 min read
- Time trialGarmin Edge data screen for time trials and triathlon: which fields to show and which to drop6 min read